Doheny's Clear-Tek Inground Solar Reel Installation & Manual

Clear-Tek Inground Solar Reel System

Follow this step-by-step guide to install, operate, and maintain your Doheny's Clear-Tek Inground Solar Reel System. This guide covers all components, assembly instructions, and tips for attaching your pool cover.

1. Check All Components

Before installation, ensure that all parts are included in the box:

  • 1 × M5X80 Screw with M5 Closed Nut
  • 1 × M5X40 Screw with M5 Open Nut
  • 2 × Wheels
  • 2 × T-Bases
  • 2 × Cotter Pins
  • 2 × Dowels
  • 2 × Tube Adapters (1 short, 1 long)
  • 3 × Washers
  • 3 × Caps
  • 1 × Wheel Handle
  • 2 × Fixations (steel pull brackets)
  • 6 × 1/2" Screws
  • 6 × 1-3/4" Screws
  • 2 × 3/4" Screws
  • 14 × Elastic Straps
  • 3 × Tubes (2 small, 1 large, approx. 8'6")

2. Installing the Wheels

  1. Adjust the axle on the T-Base so it is visible from both ends.
  2. Slide the Wheel onto the axle.
  3. Place the small washer on the axle.
  4. Insert the Cotter Pin through the axle and bend outward to lock it.
  5. Slide the Cap into place (see Figure 1 in PDF, page 2).
  6. Repeat for the second wheel.

3. Installing the Wheel Handle

  1. Insert the Elastic Straps into the grooves of the Tube. Ensure even placement for proper support.
  2. Slide the large Tube Adapter into the T-Base.
  3. Insert the Dowel into the Tube Adapter at a 90° angle to lock it in place (see Figure 3 in PDF, page 3).
  4. Slide the Wheel Handle onto the top of the base. Line up the screw hole with the pre-drilled hole in the Tube Adapter axle. A rubber mallet may help if needed.
  5. Secure with M5X80 Screw and M5 Closed Nut.

4. Installing the Tube Adapter to the Base

  1. On the opposite side of the Wheel Handle, insert the Tube Adapter into the top of the base.
  2. Slide the Dowel into the Tube Adapter.
  3. Place the Washer into the Tube Adapter.
  4. Secure with M5X40 Screw and M5 Open Nut.
  5. Slide the Cap into place. A rubber mallet may be required.

5. Installing the Tubes

  1. Attach the small tube to the Tube Adapter, exposing the three screw holes on each end.
  2. Attach the large tube, followed by the second small tube.
  3. Secure tubes to adapters using 1-3/4" screws and a drill (see Figure 4 in PDF, page 3).
  4. Use 1/2" screws to secure the tubes further (see Figure 5 in PDF, page 3).

6. Attaching the Pool Cover

  1. Position the Solar Reel near the pool edge for rectangular pools, or at the midpoint for irregular pools.
  2. Carefully punch a hole in the cover using scissors or a screwdriver.
  3. Insert the Elastic Strap into the cover casing (see Figure 6 in PDF, page 3).
  4. Unfold the Elastic Strap to lock it securely in place (see Figure 7 in PDF, page 3).
  5. If the reel is offset, fold the cover where the Elastic Straps attach so the straps pass through both sides.

7. Attaching the Fixation (Steel Bracket)

  1. Adjust tube length to fit your pool width.
  2. Slide the Fixation into the groove and line up the indentation with the screw line.
  3. Insert the 3/4" Screw next to the bracket and drill into place. The Fixation Screw locks the tube in place.
  4. Repeat for the second fixation on the opposite side of the reel.

Maintenance Tips

  • Inspect the Solar Reel regularly for wear or loose screws.
  • Keep the tubes and Elastic Straps clean and free from debris.
  • Store indoors during off-season or cover to prevent UV damage.
  • Do not force any components; use gentle pressure or a rubber mallet as needed.

For more information on pool cover care and solar reel accessories, visit our Solar Reel & Pool Cover page.

Download