Hayward
TriStar® VS
SP3202VSP, SP3202VSPND
Hayward's TriStar VS variable speed pump delivers incredible energy savings via its advanced hydraulic design combined with a totally enclosed, permanent magnet motor. TriStar VS is easily installed either as a programmable stand-alone pump or with a Hayward or third party controller and features an easy-to-use digital control interface that can be mounted in four different positions on the pump or removed and mounted on the wall for total user convenience.
Note: To prevent potential injury and to avoid unnecessary service calls, read this manual carefully and completely. Unless otherwise stated, instruction in this manual apply to both pump models.
Table of Contents
| 1. | Important Safety Instructions | 4 |
| 2. | General Information | 7 |
| 2.1 | Introduction | 7 |
| 2.2 | Primary Features | 7 |
| 2.3 | Product Dimensions | 7 |
| 3. | Energy Efficiency Overview | 8 |
| 4. | Installation and Wiring | 8 |
| 4.1 | Pump Location | 8 |
| 4.2 | Pump Mounting | 9 |
| 4.3 | Pipe Sizing Chart | 9 |
| 4.4 | Plumbing | 9 |
| 4.5 | Electrical | 10 |
| 4.6 | Electrical Specs | 10 |
| 4.7 | Voltage | 10 |
| 4.8 | Grounding and Bonding | 10 |
| 4.9 | Wiring | 10 |
| 4.10 | Remote Control Wiring/Operation | 11 |
| 4.11 | Digital Control Interface Orientation (SP3202VSP only) | 11 |
| 4.12 | Interface Wall Mounting (SP3202VSP Only) | 12 |
| 4.13 | Installation Procedure | 14 |
| 5. | Wiring Diagrams | 15 |
| 5.1 | Input Power Wiring (Required) | 15 |
| 5.2 | Wall Mounted Digital Control Interface Wiring (SP3202VSP only; Optional) | 15 |
| 5.3 | External relay Speed Control Wiring (SP3202VSP only; Optional, for remote selection of pump speed) | 16 |
| 5.4 | Hayward Automation Control Wiring (Optional, for remote control of pump speed) | 17 |
| 5.5 | Remote Stop Switch Wiring (Optional) | 18 |
| 6. | Start-Up & Operation | 18 |
| 6.1 | Prior to Start-Up | 18 |
| 6.2 | Starting/Priming the Pump | 19 |
| 6.3 | User Interface Summary (SP3202VSP only) | 20 |
| 6.4 | Menu Outline (SP3202VSP only) | 21 |
| 6.5 | Initial Startup (SP3202VSP only) | 21 |
| 6.6 | Configuration Menu (SP3202VSP only) | 22 |
| 6.7 | Timer Menu (SP3202VSP only) | 23 |
| 6.8 | Preset Speed Setup Meny (SP3202VSP only) | 24 |
| 6.9 | Diagnostic Menu (SP3202VSP only) | 24 |
| 6.10 | Stop/Resume (SP3202VSP only) | 25 |
| 6.11 | Quick Clean (SP3202VSP only) | 25 |
| 6.12 | Remote Stop | 26 |
| 7. | Maintenance | 26 |
| 8. | Storage/Winterization | 26 |
| 8.1 | Storing Pump for Winterization | 26 |
| 9. | Shaft Seal Change Instructions | 27 |
| 9.1 | Removing the Motor Assembly | 27 |
| 9.2 | Removing the Impeller | 27 |
| 9.3 | Removing the Ceramic Seat | 27 |
| 9.4 | Seal Installation | 27 |
| 9.5 | Replacing the Impeller and Diffuser | 28 |
| 9.6 | Replacing the Motor Assembly | 28 |
| 10. | Replacement Parts | 28 |
| 10.1 | Parts Diagram | 28 |
| 10.2 | Parts Listing | 29 |
| 11. | Troubleshooting | 30 |
| 11.1 | General Problems | 30 |
| 11.2 | Check System Messages | 32 |
| 12. | Warranty | 33 |
| 13. | Product Registration | 33 |
